FuelTech FT600 EFI System 3010004009 Engine Management System, FT600, EFI System, Without Harness, Each

Otto cycle engine control for 1, 2, 3, 4, 5, 6, 8, 10 and 12 cylinders;
Wankel engine control (rotary) for 2, 3 and 4 rotors;
Full sequential ignition control, semi-sequential and multipoint control;
Ignition control through trigger wheel or distributor;
Full sequential ignition or wasted spark;
Closed loop injection through oxygen sensor (wide band lambda sensor)1;
AMP SUPERSEAL automotive connectors;
Electronic throttle body Control (Drive-By-Wire);
Ignition timing and actuator based Idle control (throttle body, step motor, or PWM valve);
Real-time adjustable maps on the screen and on the FT Manager software;
Aluminum case with IP67 certified waterproof seals (capable to withstand up to 1 hour under 1.65 feet of water).
Differential input for RPM signal;
Differential input for cam sync signal;
20 input channels which are completely adjustable – digital and analogic (temperature, pressure, speed and position sensors, TPS, external MAP, buttons, keys, etc.);
2 inputs with a high gain preamplifier usually used with a strain gage sensor;
Adjustable sensor reading scale;
Speed sensor and integrated gyroscope;
Internal MAP sensor of 7 bar (1 bar vacuum and 6 bar positive pressure);
1 USB port for computer and Fuel Tech software connection;
2 CAN ports for Fuel Tech FTCAN 2.0 or FTCAN 1.0 (communication with Fuel Tech WB-O2 Nano, Fuel Tech EGT-8 CAN, Racepak IQ3 (requires Racepak Universal Interface Module), Fuel Tech FTSPARK, VNET, Aim, etc.) OEM CAN partial compatibility with: C6 Corvette, C7 Corvette, 5th gen Camaro, 2009 CTS-V Cadillac.
32 general-purpose outputs: (all of which can be used for general accessories as fuel pump, thermotic fans, valves, injectors, solenoids, etc.);
16 open collector outputs: recommended for high impedance injectors (up to 4 injectors per output) – it is possible to set up to 32 injectors using external Fuel Tech Peak and Hold ECU;
8 open collector outputs with a 5V current source of: recommended for ignition control;
8 PUSH-PULL or HALF BRIDGE outputs: suitable for ignition, step motor control, electronic throttle body and to activate loads by 12V instead of ground.
Screen dashboard which displays different sizes and styles to be used with any existing equipment or sensor;
Dashboard can have up to 4 screens with navigation through the screen or external button;
Upper tab with 10 LED lights, colored RGB and adjustable progressive shift light;
4 RGB LED side lights which can be triggered by 3 different combined settings;
Diagnosis dashboard with real-time information of all inputs, outputs, CAN engine start diagnosis and Status Events;
Customizable splash screen allows the user to select the image shown on the FT550 start up screen.
Full sequential injection for up to 24 outputs;
Closed loop fuel control through O2 sensor (wide band sensor)*;
2 injection banks (Bank A and bank B);
Primary map though MAP, TPS or RPM;
Advanced 3D primary map with up to 32x32 cells (completely adjustable map index and size);
Simplified 2D map with up to 1x32 cells by MAP or TPS and RPM compensation of up to 1x32 cells (completely adjustable map index and size);
Injection time resolution of 0,001ms;
Acceleration fuel enrichment and decay adjustment;
Individual cylinder trim setting by MAP or RPM;
Injector compensation through:
- Engine temperature
- Air temperature
- Battery voltage (individual per bank)
- TPS or MAP
- Starting engine map with the engine temperature
- Prime pulse table
- Post start enrichment
- Gear based fuel compensation
- Gear shift fuel compensation
- Fuel injection angle table
- Injectors deadtime compensation by battery voltage.
* An external wide band lambda sensor conditioner is required – Fuel Tech WB-O2 Nano, Alcohol-O2, WBO2 Datalogger, etc.);

Sequential ignition for up to 12 cylinders;
Main map by MAP, TPS or RPM;
Advanced 3D primary map with up to 32x32 cells (completely adjustable map index and size);
Simplified 2D map with up to 1x32 cells per MAP or TPS and RPM compensation of up to 1x32 cells (completely adjustable map index and size);
Injection angle resolution of 0,01°;
Individual cylinder injection settings;
Ignition timing compensation by air temperature;
Ignition timing compensation by engine temperature;
Gear based timing compensation;
Gear shift timing compensation.
Multiple session recording (files) logs up to 256 channels;
Simplified mode with sample rate of 25, 50, 100 or 200Hz;
Advanced mode allows individual settings for the sample rate with 1, 5, 25, 50, 100 or 200Hz;
Automatic activation by RPM, through the screen or by external button;
Data storage for up to 2h50min (24 channels at 25Hz);
FT Manager Datalogger Software for viewing and comparing logs.
Burnout mode, 2-step, 3-step;
Ignition timing map for drag Racing features;
Line lock brake output;
Brake pressure control by line lock;
2-step activation by speed, boost, MAP or clutch position;
Time based RPM limiter by timing retard or ignition cut;
Time based wheel speed or driveshaft RPM control with timing retard or ignition cut;
Time-based ignition timing compensation ;
Time-based fuel compensation;
Pro-Nitrous setting for up to 6 stages, with activation control, fuel enrichment and ignition timing maps;
Gear shift output;
Time based output;
Staging control;
Wheelie Control.
Integrated Gear Controller : ignition cut for clutch less gear shifting's using a strain gage sensor on the shifter;
Integrated Boost Controller: wastegate valve pressure control;
Idle speed control by timing, step motor, PWM valve or electronic throttle body;
Deceleration fuel cutoff;
Control of up to two thermotic fans through engine temperature or air conditioning, one of the outputs can drive a solid-state using PWM control for soft starting the fans;
Air conditioning control;
Fuel pump control – with 6s prime;
Variable Valve Timing (VTEC) control;
Progressive nitrous control with fuel enrichment and timing retard;
Generic duty cycle – PWM control;
Boost activated output;
RPM activated output;
Different options for gear detection: RPM drop, analogic sensor, pulse, speed and gear ratio, by gear shift output or Gear Controller;
Start button. Allows to start and shut down the engine via a relay connected to an output switching the starter;
Cold start with external reservoir;
Differential control for Yamaha YXZ1000 UTV;
Active traction control keeps wheel slip on ideal levels for maximum traction, thus adapting the available traction conditions as it seeks to maintain the programmed wheel speed difference by reading traction wheel and reference wheel speed difference;
Hi-resolution engine power control method for RPM limiter. Controls timing on each cylinder and considerably reduces the turbo spool time in a trans brake/2-step rev limiter, keeps cylinders and spark plugs in conditions of maximum efficiency (they never get wet because they always fire), allow to lower the RPM limiter for launch or to make more boost at the same RPM and smoothens the 2-step limiter operation for less vibration. (Patent pending);
Pit Limit / Speed Limit;
Generic outputs allow to configure up to 8 outputs by associating an input and setting up the way the output will be activated.
Default sensors make the configuration easier:
Oil pressure
Fuel pressure
External MAP sensor (GM 1 bar, GM 1.05 bar, GM 2 bar, GM 3 bar, GM 3.05 bar)
Nitrous bottle pressure
Clutch pressure
Wastegate pressure
Brake pressure
Back pressure
Pan Vacuum
Transmission pressure
Torque converter pressure
Engine coolant pressure
Air temperature
Engine temperature
Exhaust gas temperature (EGT)
Transmission temperature
Intercooler temperature
Tire temperature
Track temperature
Clutch position
Shock position
Wheel speed
Turbocharger speed (up to 2)
Driveshaft RPM
Input shaft RPM
Ride height sensor
Pitch rate sensor
Flex Fuel sensor
RPM limiter by fuel or ignition cut;
Shift light with sound and dashboard alert and/or external shift light;
Configurable safe mode options (RPM limit or engine shutoff);
High or low exhaust gas temperature (EGT), O2 closed loop limit, over boost, over rev, engine temperature, duty cycle, oil pressure, fuel pressure and differential fuel pressure.
FT Manager has several tools and features:
Real-time map edition
Edition of the indexes of map tables
Save and read saved maps on the PC
Open maps from log files
Display fuel maps in MS, %VE, %DC and lb./h
Easy edition of time-based controls, organizing all in one screen and making it possible to use a log file as reference
Pro Nitrous edition aided by the stage chart
Allows converting maps of previous ECUs (FT200, FT250, FT300, FT350 and FT400)
Allows importing of some specific tables from other maps
ECU software upgrades
Splash screen customization
Engine operation in real time analysis through gauges and graphics with full screen option
Check alert and status messages
Test time-based features
Edit channels of the internal datalogger and their individual logging rates
Switch between basic (2D) or advanced (3D) maps
Edit the odometer and hour meter
Reset the ECU to factory default
Recalibrate the touchscreen
View all devices connected to the CAN network
Receive warnings about new updates
Internet Remote Tuning allows connecting to another FT Manager over the internet, for giving or receiving remote support
FT Datalogger:
Download and analyze log files from Power FT ECUs
Log files comparison
Mathematical channels
Data export to CSV file
Overlay functions easily show which cell the engine was running on for better data analysis:
Fuel tables overlay
Ignition tables overlay
Closed loop corrections: allows the user to see and apply all the corrections applied by the O2 closed loop on a log file.
Select between light or dark background for better data visualization
Select if you want to show channels names and values on the chart or only in the preview panel
Full timeline visualization
Set log zero time (tell the log time where the car launched)
Erase your ECU datalogger memory
Trim feature for log files – makes them smaller and have only the information you need
Fuel Tech Data Log App:
Open your log files on your phone`s screen (up to 4 channels at the same time) - (Android and iOS).
Product FT600 EFI: 5.86 x 3.7 x 2.42 in;
FT600 packaging: 12.2 x 8.86 x 3.33 in;
Shipping box: 13 x 9.45 x 5.9 in.
Product FT600 EFI: 20.74 oz;
FT600 EFI packaging without harness: 61.44 oz;
FT600 EFI packaging with a 10 ft harness: 117.25 oz;
Product Weight “FT600 10 ft harness”: 55.8 oz.
1 year
1 FT600 EFI;
1 operation and installation guide;
1 mounting kit (4 rubber mounts, 4 washers and 4 ¼” nuts);
1 protection cover for the FT600 ECU;
1 mini USB cable;